use common::gpio;
use common::nvic;
use common::i2c;
+use common::spi;
use common::uart;
use common::usb_serial;
use common::display;
}
}
+fn reset_requested() -> bool {
+ let pta1 = gpio::get(gpio::GPIOA) & (1 << 1);
+ let pte25 = gpio::get(gpio::GPIOE) & (1 << 25);
+
+ (pta1 | pte25) == 0
+}
+
#[inline(never)]
#[panic_handler]
fn panic(_info: &core::panic::PanicInfo) -> ! {
loop {
+ if reset_requested() {
+ nvic::system_reset();
+ }
}
}
+fn configure_push_buttons() {
+ // Configure lower right push button.
+ gpio::set_direction(gpio::GPIOA, 1 << 1, gpio::Direction::Input);
+ port::set_af(port::PORTA, 1, 1);
+ port::set_pull(port::PORTA, 1, port::Pull::Up);
+
+ // Configure upper right push button.
+ gpio::set_direction(gpio::GPIOA, 1 << 12, gpio::Direction::Input);
+ port::set_af(port::PORTA, 12, 1);
+ port::set_pull(port::PORTA, 12, port::Pull::Up);
+
+ // Configure lower left push button.
+ gpio::set_direction(gpio::GPIOE, 1 << 24, gpio::Direction::Input);
+ port::set_af(port::PORTE, 24, 1);
+ port::set_pull(port::PORTE, 24, port::Pull::Up);
+
+ // Configure upper left push button.
+ gpio::set_direction(gpio::GPIOE, 1 << 25, gpio::Direction::Input);
+ port::set_af(port::PORTE, 25, 1);
+ port::set_pull(port::PORTE, 25, port::Pull::Up);
+
+ // Configure middle left push button.
+ gpio::set_direction(gpio::GPIOE, 1 << 31, gpio::Direction::Input);
+ port::set_af(port::PORTE, 31, 1);
+ port::set_pull(port::PORTE, 31, port::Pull::Up);
+}
+
#[no_mangle]
pub unsafe extern "C" fn _start() -> ! {
clock::configure();
gpio::set_direction(gpio::GPIOB, 1 << 16, gpio::Direction::Output);
port::set_af(port::PORTB, 16, 1);
+ // Configure pin for the MX25L's chip select line.
+ gpio::set_direction(gpio::GPIOD, 1 << 0, gpio::Direction::Output);
+ port::set_af(port::PORTD, 0, 1);
+ gpio::set(gpio::GPIOD, 1 << 0);
+
+ // Configure pins for SPI0.
+ port::set_af(port::PORTD, 1, 2);
+ port::set_af(port::PORTD, 2, 5);
+ port::set_af(port::PORTD, 3, 5);
+
+ spi::configure(spi::SPI0);
+
+ nvic::disable_irq(10); // SPI0
+
// Configure pins for UART0.
port::set_af(port::PORTE, 20, 4);
port::set_af(port::PORTE, 21, 4);
gpio::set_direction(gpio::GPIOB, 1 << 1, gpio::Direction::Output);
port::set_af(port::PORTB, 1, 1);
- // Configure upper right push button.
- gpio::set_direction(gpio::GPIOA, 1 << 12, gpio::Direction::Input);
- port::set_af(port::PORTA, 12, 1);
- port::set_pull(port::PORTA, 12, port::Pull::Up);
+ configure_push_buttons();
enable_interrupts();
}
});
- if (gpio::get(gpio::GPIOA) & (1 << 12)) == 0 {
+ if reset_requested() {
nvic::system_reset();
}
}